The step-by-step sequence<\/p>\n
Open the container from the hydrophone side, using the key provided if necessary.
\nIt is not necessary to open the opposite side of the container.<\/p>\n
If the batteries are in good condition (and you know this because you have recently tested them) you can restart and reprogram the recorder using the magnet directly from outside the container, without reopening the cylinder. This can be useful during field work. To reboot the units the magnet must remain near the small golden cylinder that you see inside near the serial number on yellow label, for at least 10 seconds, when you remove it the recorder will reboot.
\nLeaving the magnet near the golden cylinder (and securing it with tape, for example) is equivalent to removing the batteries and interrupts the power supply.
\nWhen the magnet is removed you should see the small LEDs light up. This is the starting sequence.<\/p>\n
Check the batteries at each use cycle and replace them if the battery tester indicates WEAK. The tester should be adjusted for 1.5V batteries. There are three possible settings (by moving the triangle beside the display: 3V, 1.5V, 1.2V. In our case it must be adjusted for 1.5V).<\/p>\n
ALWAYS program a new sampling period each time you restart the recorder, so you can be sure that the pattern is correct and that the clock is synchronized.<\/p>\n
The safest way to go is this sequence!Lan<\/p>\n
Launch the UM384BLE app on the device used to program
\nchoose CONNECT TO MIC
\nchoose SCAN & CONNECT
\nput the batteries in, or place the magnet and then remove it after ten seconds
\nat this point it should be connected to the phone. check
\nchoose TIMING
\nchoose MODE REPEAT
\nconfirm with OK
\nchoose ADD TIME
\nchoose SET FOR NOW if you intend to start soon, or SET DATE AND TIME if sampling starts on a later day
\nchoose the duration of the recordings (12 hrs = 12:00 … 15 minutes = 00:15)
\nchoose the duration of the pause between recordings (minimum 1 min = 00:01)
\nfor TURSIONET search i the standard recording period is 15 min (00:15) followed by 5 min break (00:05)
\nchoose 192kHz SAMPLING RATE
\nignore the TRIGGER tab
\nchoose the OTHER tab and write in the DEVICE NAME field the serial number of the unit (the one on the label) 22D?
\nleave File Split Size in Min (minutes)
\nFile Size in minutes can be adjusted to 15 minutes
\nConfirm and go to the CONNECT tab
\npress SEND TIME
\npress SEND CONFIG
\nwait for the program to transfer successfully
\nthe unit restarts and goes into pause, ready to begin sampling according to the rules you set<\/p>\n
Translated with www.DeepL.com\/Translator (free version)<\/p>\n","protected":false},"excerpt":{"rendered":"
The step-by-step sequence Open the container from the hydrophone side, using the key provided if necessary. It is not necessary to open the opposite side of the container. If the batteries are in good condition (and you know this because you have recently tested them) you can restart and reprogram […]<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":130,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_uag_custom_page_level_css":"","footnotes":""},"class_list":["post-132","page","type-page","status-publish","hentry"],"translation":{"provider":"WPGlobus","version":"3.0.6","language":"en","enabled_languages":["it","fr","en"],"languages":{"it":{"title":true,"content":true,"excerpt":false},"fr":{"title":true,"content":true,"excerpt":false},"en":{"title":true,"content":true,"excerpt":false}}},"uagb_featured_image_src":{"full":false,"thumbnail":false,"medium":false,"medium_large":false,"large":false,"1536x1536":false,"2048x2048":false},"uagb_author_info":{"display_name":"admin","author_link":"https:\/\/www.tursionet.eu\/en\/author\/admin\/"},"uagb_comment_info":0,"uagb_excerpt":"The step-by-step sequence Open the container from the hydrophone side, using the key provided if necessary. It is not necessary to open the opposite side of the container. If the batteries are in good condition (and you know this because you have recently tested them) you can restart and reprogram […]","_links":{"self":[{"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/pages\/132","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/comments?post=132"}],"version-history":[{"count":7,"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/pages\/132\/revisions"}],"predecessor-version":[{"id":233,"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/pages\/132\/revisions\/233"}],"up":[{"embeddable":true,"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/pages\/130"}],"wp:attachment":[{"href":"https:\/\/www.tursionet.eu\/en\/wp-json\/wp\/v2\/media?parent=132"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}